2010+ TOYOTA 4RUNNER
CLICK HERE FOR ALL SHOCK FEATURES & BENEFITS
Note(s): 9, 10 + Install TIme: 3.5 Hours
Note(s): 9 + Install TIme: 3.5 Hours
FEATURES & BENEFITS:
-
Falcon Shock & Spacer Lift Systems provide additional rear travel and ride height
-
Long-travel rear shocks matched to the included rear lift coil spring spacers
+ FITS: 2010+ Toyota 4Runner +
• Does NOT fit TRD Pro models
+ LIFT HEIGHT: Front: 0-2" | Rear: 1" +
+ MAX TIRE SIZE: 285/70R17 +
INCLUDES:
FRONT:
-
Sport Leveling Monotube Shocks (0-2” Lift)
-
Microcellular “foam” Progressive Bump Stops
-
Billet coil spring carriers
-
Injection-molded squeak-free spring isolators
-
All necessary hardware
REAR:
-
1" lift coil spring spacers
-
Long-travel Sport Tow/Haul Adjustable Piggyback Shocks (1” Lift)
-
Microcellular “foam” Progressive Bump Stops
-
Bump stop cups
-
Roost guards
-
All necessary hardware
INCLUDES:
FRONT:
-
Sport Leveling Monotube Shocks (0-2” Lift)
-
Microcellular “foam” Progressive Bump Stops
-
Billet coil spring carriers
-
Injection-molded squeak-free spring isolators
-
All necessary hardware
REAR:
-
1" lift coil spring spacers
-
Long-travel Sport Piggyback Shocks (1” Lift)
-
Microcellular “foam” Progressive Bump Stops
-
Bump stop cups
-
Roost guards
-
All necessary hardware
NOTE(S):
-
Bump stop configuration varies depending on shock absorber collapsed length, tire size, and fenders – See instructions for proper configuration for your application.
-
May require JL: TeraFlex 2” Bump stop Strike Pad Extension Kit (# 1959500) and/or JL: TeraFlex 0.5” Bump Stop Strike Pad Shim Kit(s) (# 1959300).
-
Cartridge Upgrade Kits NOT available for TJ: Series 3.0 Piggyback Shocks.
-
Requires cutting of stock lower shock mount.
-
Raw finish for optional welding – welding not required, but highly recommended for extreme use.
-
3 shock mounting heights possible (stock height; + 0.8”; + 1.6”).
-
Mounting at Level 2 or Level 3 may affect overall rear axle travel, causing the axle to droop further, which may cause the spring to fall out of place.
-
NOT compatible w/ JK: TeraFlex High Steer Systems (w/ HD Drag Link Flip Kit & HD Tie Rod: # 4391000; w/ HD Drag Link Flip Kit – No HD Tie Rod: # 4390975; w/ Drag Link End: # 4390875) or TeraFlex High Steer Knuckles (# 4390870).
-
Never exceed factory tow/haul ratings.
-
Do not use tow/haul modes while unladen as the increased rear stiffness could upset the balance between the front and rear of the vehicle, which could lead to loss of vehicle control.
-
Does NOT fit Ford F-150 Raptor.
-
Rear shocks require existing lift kit’s rear bump stop blocks.
-
Does NOT fit Dodge/Ram trucks equipped w/ Active-Level Four-Corner Air Suspension.
-
Does NOT fit Chevrolet/GMC trucks equipped w/ Magnetic Ride Control.
-
Fits U.S.-spec Ford Ranger ONLY – does NOT fit international models.
-
When installing Falcon Ford Ranger front leveling shocks above stock ride height, an upper control arm designed for 1-3” lifts is required to achieve proper alignment.
-
Does NOT fit Ford F-250 2WD model.
-
These shocks work with stock height Ford F-250 vehicles or w/ up to a 2” leveling kit – does NOT include front lift coil springs or front lift coil spring spacers.
-
Ford F-250 2” front lift coil springs or front lift coil spring spacers can be purchased from the aftermarket.